Adtran MX2800 M13 Bedienungsanleitung Seite 90
- Seite / 200
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4-6 61200290L1-1G
Section 4, Status MX2800 M13 Multiplexer User Manual
5. DS2 STATE
This field displays the current state of each of the seven DS2s. Possible states are listed in Tab le 4-8.
6. T1/E1 STATE
This field displays the current state of the individual T1s or E1s. Possible states are listed in Table 4-9.
NOTE
A DS2 can be divided into either three E1s or four T1s. Therefore, when
dealing with an E1 configuration, some of the fields in the
T1/E1 State
menus do not apply (and display nothing).
7. ACKNOWLEDGE ALARMS (ACO)
This selection is used to remotely turn off an active alarm. It is the software equivalent of the ACO button
as described in ACO Buttons on page 2-15.
Table 4-8. DS2 States
Condition Description
OK The DS2 is not receiving alarms.
LOF The unit detects framing loss across the DS2.
RAI The unit is receiving an RAI (yellow) alarm across the DS2. This alarm is a signal
sent back toward the source of a failed transmit circuit. The X-bit is set to zero.
AIS The unit is receiving an AIS (blue) alarm condition from the network across the
DS2. AIS alarms occur when the unit receives unframed all ones.
Table 4-9. T1/E1 States
Condition Description
OK The T1/E1 is ready to pass data.
LOS The unit has lost the Rx signal on the T1/E1.
XCV The unit is receiving excessive code violations across the T1/E1, exceeding the
configured threshold (refer to XCV Threshold on page 3-15).
TST The T1/E1 is currently in test mode.
HOT The T1/E1 transceiver temperature is too high.
LAIS The T1 is receiving all ones from the DSX-1 interface.
CAIS The T1 is receiving all ones from the DS3 side of the network.
- MX2800 M13 Multiplexer 1
- User Manual 1
- Trademarks 2
- To the Holder of the Manual 2
- Revision History 3
- Conventions 3
- Training 5
- Contents 7
- 61200290L1-1G ix 9
- Section 4 10
- Section 5 11
- 61200290L1-1G xiii 13
- 61200290L1-1G xv 15
- 61200290L1-1G xvii 17
- Section 1 19
- Product Overview 19
- 3. T3 OVERVIEW 20
- Network Manager 20
- 61200290L1-1G 1-3 21
- Fan Faceplate (P/N 1200466L1) 22
- Section 2 23
- Installation and Operation 23
- 4. POWER UP 24
- 61200290L1-1G 2-3 25
- PWR FAIL 25
- 5. RACKMOUNT INSTALLATION 26
- FRONT VIEW 27
- REAR VIEW 27
- 6. REAR PANEL 28
- LAN Port 29
- Modem Port 29
- DSX-3 Interfaces 29
- DSX-1/E1 Interfaces 30
- Power Connection 30
- 7. FRONT PANEL 30
- Craft Port 30
- Main Menu 31
- Navigating Within the Menus 32
- 61200290L1-1G 2-11 33
- Configuration 34
- Figure 2-9. Loopback Menu 35
- CTRL+]) 36
- ACO Buttons 37
- LED Descriptions 37
- T1/E1 Status LEDs 39
- 2-18 61200290L1-1G 40
- Section 3 41
- Configuration menu tree 42
- 61200290L1-1G 3-3 43
- 2. NETWORK INTERFACE 44
- DS3 Configuration 44
- Remote Loopbacks 45
- Protection Configuration 46
- Miscellaneous 47
- DS2 Configuration 47
- 3. T1/E1 INTERFACE 48
- T1/E1 Line Coding 50
- T1/E1 Line Length 51
- T1/E1 Loopback Detection 52
- T1/E1 Circuit Protection 53
- T1/E1 Line Identification 54
- XCV Threshold 55
- 4. SYSTEM MANAGEMENT 56
- Management Options 57
- DS3 Remote IP Address 58
- DS3 IP MTU 58
- Dialup Options 58
- 61200290L1-1G 3-19 59
- 3-20 61200290L1-1G 60
- SNMP Management Options 61
- 3-22 61200290L1-1G 62
- 61200290L1-1G 3-23 63
- Read Community Name 64
- Network Date/Time Option 65
- System Security 66
- RADIUS Authentication 67
- 3-28 61200290L1-1G 68
- Shared Secret 69
- Response Timeout 69
- Maximum Retries 69
- 3-30 61200290L1-1G 70
- 61200290L1-1G 3-31 71
- 3-32 61200290L1-1G 72
- Date and Time 73
- 3-34 61200290L1-1G 74
- Equipment Identification 75
- 3-36 61200290L1-1G 76
- Syslog Setup 77
- 5. UTILITIES 78
- Loading Default Settings 79
- Updating Software 80
- Update Via TFTP Server 81
- Configuration Transfer 82
- Resetting the System 83
- 3-44 61200290L1-1G 84
- 4-2 61200290L1-1G 86
- 61200290L1-1G 4-3 87
- 3. POWER SUPPLY STATE 88
- 4. SYSTEM STATE 88
- Protection 89
- Card Comm 89
- 5. DS2 STATE 90
- 6. T1/E1 STATE 90
- 7. ACKNOWLEDGE ALARMS (ACO) 90
- Statistics 91
- DS3 Statistics 92
- Condition Description 93
- 5-4 61200290L1-1G 94
- 61200290L1-1G 5-5 95
- 5-6 61200290L1-1G 96
- Figure 5-6 on page 5-6 97
- 5-8 61200290L1-1G 98
- DS2 Statistics 99
- 5-10 61200290L1-1G 100
- LEFT and 101
- 5-12 61200290L1-1G 102
- T1/E1 Statistics 103
- Performance Parameters 104
- Alarm Log 104
- Figure 5-14. Alarm Log 105
- 5-16 61200290L1-1G 106
- Section 6 107
- Loopbacks 107
- 2. T1/E1 LOOPBACKS 108
- Data Mode 108
- Tributary 108
- Analog Network 109
- Digital Line/Net 109
- Codec Line/Net 110
- Remote Loopback 110
- CSU Loopback 110
- CSU Loopback w/BERT 110
- Line BERT 111
- 3. DS3 LOOPBACKS 112
- Line Loopback 113
- Digital Loopback 113
- Metallic Loopback 114
- Remote All T1/E1 114
- 4. DS2 LOOPBACKS 115
- DS2 Network 115
- 6-10 61200290L1-1G 116
- Section 7 117
- 7-2 61200290L1-1G 118
- 61200290L1-1G 7-3 119
- 7-4 61200290L1-1G 120
- Section 8 121
- Power Loss Recovery 121
- 3. POWER SUPPLY RECOVERY MODE 122
- 5. BATTERY BACKUP MODE 123
- Battery Charger 124
- Power Cable 124
- Section 9 125
- Transaction Language 1 (TL1) 125
- 9-2 61200290L1-1G 126
- 3. TL1 MESSAGES 127
- TL1 Responses 127
- Output Response Messages 128
- Autonomous Messages 128
- 4. TL1 COMMANDS 129
- 9-6 61200290L1-1G 130
- 61200290L1-1G 9-7 131
- 9-8 61200290L1-1G 132
- 61200290L1-1G 9-9 133
- 9-10 61200290L1-1G 134
- TL1 Autonomous Messages 135
- 9-12 61200290L1-1G 136
- 61200290L1-1G 9-13 137
- 9-14 61200290L1-1G 138
- 61200290L1-1G 9-15 139
- 9-16 61200290L1-1G 140
- 5. TL1 ERROR CODES 141
- TL1 Editing 141
- TL1 Editing Examples: 142
- 61200290L1-1G 9-19 143
- Data Dictionaries 144
- 61200290L1-1G 9-21 145
- 9-22 61200290L1-1G 146
- 61200290L1-1G 9-23 147
- 9-24 61200290L1-1G 148
- 61200290L1-1G 9-25 149
- 9-26 61200290L1-1G 150
- 61200290L1-1G 9-27 151
- 9-28 61200290L1-1G 152
- 61200290L1-1G 9-29 153
- TL1 Loopback Commands 154
- 61200290L1-1G 9-31 155
- 9-32 61200290L1-1G 156
- Appendix A 157
- Acceptance Test Procedure 157
- 3. CONFIGURING THE SYSTEM 158
- Accessing the Craft Port 158
- Provisioning the DS3 Port 158
- 61200290L1-1G A-3 159
- , and follow the prompts 159
- Provisioning the DS1 Ports 160
- Alarm Relay Configuration 161
- DS1 to DS3 Head-to-Head Test 162
- DS1 to DS3 (Hard) Loopback 163
- Critical Alarm Relay Test 163
- Noncritical Alarm Relay Test 164
- Power Supply Redundancy 164
- 61200290L1-1G A-9 165
- Controller Card Redundancy 166
- 7. RESTORING DEFAULT SETTINGS 166
- 61200290L1-1G A-11 167
- A-12 61200290L1-1G 168
- Appendix B 169
- N4200290L4) 170
- 61200290L1-1G B-3 171
- B-4 61200290L1-1G 172
- Appendix C 173
- Specifications Summary 173
- Clocking 174
- Management 174
- Agency Approvals 175
- Environment 175
- Physical 175
- C-4 61200290L1-1G 176
- Appendix D 177
- Acronyms/Abbreviations 177
- D-2 61200290L1-1G 178
- 61200290L1-1G D-3 179
- D-4 61200290L1-1G 180
- 61200290L1-1G D-5 181
- D-6 61200290L1-1G 182
- Appendix E 183
- Glossary 183
- E-2 61200290L1-1G 184
- 61200290L1-1G E-3 185
- E-4 61200290L1-1G 186
- 61200290L1-1G E-5 187
- E-6 61200290L1-1G 188
- 61200290L1-1G E-7 189
- E-8 61200290L1-1G 190
- Appendix F 191
- Warranty 191
- F-2 61200290L1-1G 192
- Numerics 193
- I-2 61200290L1-1G 194
- 61200290L1-1G I-3 195
- I-4 61200290L1-1G 196
- 61200290L1-1G I-5 197
- T1/E1 State 198
Verwandte Produkte und Handbücher für Hardware Adtran MX2800 M13
Hardware Adtran 48 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Hardware Adtran 1248 Bedienungsanleitung
(236 Seiten)
(236 Seiten)
Hardware Adtran 1200F Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Hardware Adtran ADSL2+ Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Hardware Adtran XRT Bedienungsanleitung
(94 Seiten)
(94 Seiten)
Hardware Adtran 600R Bedienungsanleitung
(264 Seiten)
(264 Seiten)
Hardware Adtran TSU 120e Bedienungsanleitung
(140 Seiten)
(140 Seiten)
Hardware Adtran 1000R Series Bedienungsanleitung
(137 Seiten)
(137 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.371 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern