ADTRAN 6310 Bedienungsanleitung PDF herunterladen

Quick Start Guide, 61700100G1-13B, June 2013 1

NETVANTA 6310

P/N 1702100G1

GETTING STARTED

Two configuration methods are available for your NetVanta 6310 unit:

• Web-based graphical user interface (GUI)

• Command line interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations for each

setting. However, using the AOS CLI may be necessary for more advanced configurations.

ACCESS THE GUI

You can access the GUI from any web browser on your network by following these steps:

1. Connect the unit to your PC, using an Ethernet cable connected to ETH 0/1 port on the back of the unit.

2. Set your PC to obtain an IP address automatically using Dynamic Host Configuration Protocol (DHCP), or

change your PC to a fixed IP address of 10.10.10.2. To change your PC’s IP address, or to set the PC to

use DHCP, navigate to Computer > Control Panel > Network Connections > Local Area Connection

> Properties > IP (TCP/IP) and select either Use this IP address or Obtain an IP address

automatically (this means you are using DHCP). If you are specifying an IP address, enter these

parameters:

IP Address: 10.10.10.2

Subnet Mask: 255.255.255.0

Default Gateway: 10.10.10.1

You do not need to enter any domain naming system (DNS) server information. After the information is

entered, select Ok twice, and close the Network Connections dialog box. If you cannot change the PC’s

IP address, you will need to change the unit’s IP address using the CLI. (Refer to the next two sections for

instructions.)

3. Enter the unit’s IP address in your browser’s address line. The default IP address is 10.10.10.1, but if you

changed the unit’s IP address enter that address in the browser line.

4. You will then be prompted for the user name and password (the default settings are admin and

password).

5. The initial GUI menu appears. You can access initial setup information by selecting Config Wizard from

the menu on the left.

Access the AOS CLI using the CONSOLE port or a Telnet session. To establish a connection to the unit’s

CONSOLE port, you need the following items:

• PC with VT100 terminal emulation software

• Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for

your terminal or PC communication port on the other end

It is best to only use the Config Wizard for new installations because some existing

settings can be lost or reset when using this wizard.

You can find VT100 terminal emulation software on most PCs by navigating to Start >

Programs > Accessories > HyperTerminal > HyperTerminal. When you have opened

a HyperTerminal session, enter the settings described in Step 4.

NETVANTA 6310 DEFAULTS

RESTORING FACTORY DEFAULTS

On units that have a console port, you cannot restore the factory defaults, but must rather erase the device’s

configuration and then reconfigure the unit to operate correctly for your network. To erase the unit’s current

configuration, follow these steps:

1. Access the unit’s CLI and enter enable at the > prompt.

2. Enter erase startup-config at the # prompt. The device will have a blank configuration upon reboot.

3. Enter reload at the # prompt to begin restarting the device. When prompted to save configuration, enter

no. When prompted to reboot, enter yes.

4. Upon reboot, you will have to reconfigure the unit using the CRAFT port. Follow the steps outlined here or

in the technical note, Accessing the Web Interface in AOS

available at https://supportforums.adtran.com.

Feature Default Value

IP Address 10.10.10.1

User Name admin

Password password

HTTP Server Enabled

Event History On

IP Routing Enabled

1 2 3 4

Inhaltsverzeichnis

Seite 1 - NETVANTA 6310

Seite 2 - CONFIGURE YOUR APPLICATION

Seite 3

Seite 4

Weitere Dokumente für Vernetzung ADTRAN 6310

Um das Dokument anzuzeigen ADTRAN 6310 Technical Information

ADTRAN 6310 Technical Information (40 Seiten)

Um das Dokument anzuzeigen ADTRAN 6310 Bedienungsanleitung

ADTRAN 6310 Bedienungsanleitung (14 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

ADTRAN 6310 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Vernetzung ADTRAN 6310 herunter. NetVanta 6310 Quick Start Guide Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Vernetzung ADTRAN 6310

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung ADTRAN 6310