ADTRAN MX2800 M13 Bedienungsanleitung Seite 135
- Seite / 198
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Section 9, Transaction Language 1 (TL1) - TL1 Commands
61200290L1-1H 9-11
* An asterisk indicates optional command blocks.
TL1 Autonomous Messages
Autonomous messages provide a mechanism for real time reporting of system events.
Although most events reported are alarms, some events are only informational. The Verb,
Mod1, and Mod2 parameters of the message indicate what type of event has occurred.
NOTE
The default setting for Autonomous message reporting is OFF.
Follow these steps to enable Autonomous message reporting:
• If it has not already been done, initiate a TL1 session by following the setup procedures and
using the
ACT-USER command.
• Use the ALW-MSG command to enable autonomous messaging. This command is
described in Table 9-2.
REPT-ALM
indicates an alarm event. Table 9-3 lists possible autonomous messages for alarm
events and includes recommended actions to take. REPT-EVT indicates an informational
event. Table 9-4 lists possible autonomous messages for informational events
SET-DAT:<tid>::<ctag>::<YY-MM-DD>,<HH-MM-SS>;
Description Sets the date and time
PARAM1 Date in YY-MM-DD format
PARAM2 Time in HH-MM-SS format
Table 9-2. TL1 Commands (Continued)
- M13 Multiplexer 1
- User Manual 1
- Trademarks 2
- To the Holder of the Manual 2
- Revision History 3
- Conventions 3
- Training 5
- RoHS Compliant 6
- Contents 7
- 61200290L1-1H ix 9
- Section 4 10
- Section 5 11
- Appendix A 13
- Appendix B 13
- 61200290L1-1H xv 15
- 61200290L1-1H xvii 17
- 61200290L1-1H xix 19
- Section 1 21
- Product Overview 21
- T3 OVERVIEW 22
- Network Manager 22
- 61200290L1-1H 1-3 23
- 1-4 61200290L1-1H 24
- Section 2 25
- Installation and Operation 25
- POWER UP 26
- 61200290L1-1H 2-3 27
- PWR FAIL 27
- RACKMOUNT INSTALLATION 28
- Connecting the Breakout Panel 29
- Connecting the E1 Patch Panel 29
- REAR PANEL 30
- LAN Port 31
- Modem Port 31
- DSX-3 Interfaces 31
- DSX-1/E1 Interfaces 32
- Power Connection 32
- FRONT PANEL 33
- Craft Port 33
- 2-10 61200290L1-1H 34
- 61200290L1-1H 2-11 35
- menu. Refer to “Section 5 36
- 61200290L1-1H 2-13 37
- CTRL+]) 38
- ACO Buttons 39
- LED Descriptions 39
- REPLACING OR INSTALLING CARDS 42
- Section 3 43
- Configuration 43
- menu tree 44
- 61200290L1-1H 3-3 45
- NETWORK INTERFACE 46
- DS3 Configuration 46
- 61200290L1-1H 3-5 47
- Protection Configuration 48
- Miscellaneous 49
- DS2 Configuration 49
- T1/E1 INTERFACE 49
- T1/E1 State 50
- 61200290L1-1H 3-9 51
- T1/E1 Line Coding 52
- T1/E1 Line Length 52
- T1/E1 Loopback Detection 53
- T1/E1 Circuit Protection 54
- T1/E1 Line Identification 55
- XCV Threshold 55
- SYSTEM MANAGEMENT 56
- Management Options 57
- 3-16 61200290L1-1H 58
- 61200290L1-1H 3-17 59
- 3-18 61200290L1-1H 60
- SNMP Management Options 61
- Table 3-3. Trap Descriptions 62
- 61200290L1-1H 3-21 63
- 3-22 61200290L1-1H 64
- Network Date/Time Option 65
- System Security 66
- Utilities 67
- Disabled 67
- Invisible 68
- 61200290L1-1H 3-27 69
- 3-28 61200290L1-1H 70
- 61200290L1-1H 3-29 71
- Date and Time 72
- 61200290L1-1H 3-31 73
- Equipment Identification 74
- 61200290L1-1H 3-33 75
- 3-34 61200290L1-1H 76
- UTILITIES 77
- Loading Default Settings 78
- Updating Software 79
- 3-38 61200290L1-1H 80
- Configuration Transfer 81
- Resetting the System 82
- 61200290L1-1H 3-41 83
- 3-42 61200290L1-1H 84
- 4-2 61200290L1-1H 86
- Section 4, Status - DS3 State 87
- 61200290L1-1H 4-3 87
- POWER SUPPLY STATE 88
- SYSTEM STATE 88
- Card A/Card B 89
- Protection 89
- Card Comm 90
- DS2 STATE 90
- T1/E1 STATE 90
- ACKNOWLEDGE ALARMS (ACO) 91
- 4-8 61200290L1-1H 92
- Statistics 93
- DS3 Statistics 94
- 61200290L1-1H 5-3 95
- 5-4 61200290L1-1H 96
- 61200290L1-1H 5-5 97
- 5-6 61200290L1-1H 98
- 61200290L1-1H 5-7 99
- DS2 Statistics 100
- 61200290L1-1H 5-9 101
- 5-10 61200290L1-1H 102
- 61200290L1-1H 5-11 103
- T1/E1 Statistics 104
- Performance Parameters 105
- Alarm Log 105
- PROTECTION SWITCH STATISTICS 105
- Figure 5-19. Alarm Log 106
- Section 6 107
- Loopbacks 107
- T1/E1 LOOPBACKS 108
- Data Mode 108
- Tributary 108
- Analog Network 109
- Digital Line/Net 109
- Codec Line/Net 109
- Remote Loopback 110
- CSU Loopback 110
- CSU Loopback w/BERT 110
- Line BERT 111
- DS3 LOOPBACKS 112
- Line Loopback 113
- Digital Loopback 113
- Metallic Loopback 114
- Remote All T1/E1 114
- DS2 LOOPBACKS 115
- DS2 Network 115
- 6-10 61200290L1-1H 116
- Section 7 117
- NONREDUNDANT MODE 118
- CIRCUIT FAILURE RECOVERY MODE 119
- 7-4 61200290L1-1H 120
- Section 8 121
- Power Loss Recovery 121
- POWER SUPPLY RECOVERY MODE 122
- 61200290L1-1H 8-3 123
- BATTERY BACKUP MODE 124
- Section 9 125
- Transaction Language 1 (TL1) 125
- 9-2 61200290L1-1H 126
- TL1 MESSAGES 127
- TL1 Responses 127
- 9-4 61200290L1-1H 128
- 61200290L1-1H 9-5 129
- TL1 COMMANDS 130
- 61200290L1-1H 9-7 131
- 9-8 61200290L1-1H 132
- 61200290L1-1H 9-9 133
- 9-10 61200290L1-1H 134
- TL1 Autonomous Messages 135
- 9-12 61200290L1-1H 136
- 61200290L1-1H 9-13 137
- 9-14 61200290L1-1H 138
- 61200290L1-1H 9-15 139
- TL1 ERROR CODES 140
- TL1 Editing 140
- 61200290L1-1H 9-17 141
- 9-18 61200290L1-1H 142
- should be T3 142
- 61200290L1-1H 9-19 143
- 9-20 61200290L1-1H 144
- 61200290L1-1H 9-21 145
- 9-22 61200290L1-1H 146
- should be T1 146
- 61200290L1-1H 9-23 147
- 9-24 61200290L1-1H 148
- 61200290L1-1H 9-25 149
- 9-26 61200290L1-1H 150
- 61200290L1-1H 9-27 151
- 9-28 61200290L1-1H 152
- 61200290L1-1H 9-29 153
- 9-30 61200290L1-1H 154
- Acceptance Test Procedure 155
- CONFIGURING THE SYSTEM 156
- Accessing the Craft Port 156
- Provisioning the DS3 Port 156
- 61200290L1-1H A-3 157
- , and follow the prompts 157
- Provisioning the DS1 Ports 158
- Alarm Relay Configuration 159
- VERIFYING THE DATA INTEGRITY 159
- DS1 to DS3 Head-to-Head Test 160
- DS1 to DS3 (Hard) Loopback 161
- VERIFYING ALARM NOTIFICATION 161
- Critical Alarm Relay Test 161
- Noncritical Alarm Relay Test 162
- VERIFYING SYSTEM REDUNDANCY 162
- Power Supply Redundancy 162
- 61200290L1-1H A-9 163
- Controller Card Redundancy 164
- RESTORING DEFAULT SETTINGS 165
- A-12 61200290L1-1H 166
- B-2 61200290L1-1H 168
- Appendix B, Pinouts 169
- 61200290L1-1H B-3 169
- B-4 61200290L1-1H 170
- Appendix C 171
- Specifications Summary 171
- Clocking 172
- Management 172
- Agency Approvals 173
- Environment 173
- Physical 173
- C-4 61200290L1-1H 174
- Appendix D 175
- Acronyms/Abbreviations 175
- D-2 61200290L1-1H 176
- 61200290L1-1H D-3 177
- D-4 61200290L1-1H 178
- 61200290L1-1H D-5 179
- D-6 61200290L1-1H 180
- Appendix E 181
- Glossary 181
- E-2 61200290L1-1H 182
- Appendix E, Glossary 183
- 61200290L1-1H E-3 183
- E-4 61200290L1-1H 184
- 61200290L1-1H E-5 185
- E-6 61200290L1-1H 186
- 61200290L1-1H E-7 187
- E-8 61200290L1-1H 188
- Appendix F 189
- Warranty 189
- F-2 61200290L1-1H 190
- Numerics 191
- 61200290L1-1H A-7 197
- Carrier Networks Division 198
- 901 Explorer Blvd 198
- Huntsville, AL 35806 198
Verwandte Produkte und Handbücher für Vernetzung ADTRAN MX2800 M13
Vernetzung ADTRAN TSU LT Bedienungsanleitung
(60 Seiten)
(60 Seiten)
Vernetzung ADTRAN 6310 Bedienungsanleitung
(14 Seiten)
(14 Seiten)
Vernetzung ADTRAN MX2800 M13 Bedienungsanleitung
(45 Seiten)
(45 Seiten)
Vernetzung ADTRAN 850 Bedienungsanleitung
(76 Seiten)
(76 Seiten)
Vernetzung ADTRAN Quad T1 IMA Spezifikationen
(12 Seiten)
(12 Seiten)
Vernetzung ADTRAN 1xN Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Vernetzung ADTRAN TSU LT Bedienungsanleitung
(64 Seiten)
(64 Seiten)
Vernetzung ADTRAN 1200105L3 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Vernetzung ADTRAN MX2800 Bedienungsanleitung
(196 Seiten)
(196 Seiten)
Vernetzung ADTRAN T200 T1 HDSL4 Spezifikationen
(16 Seiten)
(16 Seiten)
Vernetzung ADTRAN 1248 Spezifikationen
(4 Seiten)
(4 Seiten)
Vernetzung ADTRAN 6310 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Vernetzung ADTRAN 850 Bedienerhandbuch
(292 Seiten)
(292 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern