ADTRAN TSU 120 Bedienungsanleitung Seite 42
- Seite / 142
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 3. Operation
3-2 TSU 120 User Manual 61202129L1-1
LED Descriptions
CSU Status
The CSU status LEDs display the operational condition of the
network interface located on the controller board in the unit.
Numeric Keypad
The numeric keypad contains the numbers
0
through
9
which are used to activate
menu items and enter information (such as
the IP address).
Shift (entering
special function
keys)
Enter special function keys by pressing
and holding
Shift
before pressing the key
representing the desired character.
To activate a special function key rather
than a number, press and hold
Shift;
then
the button. See Operation Keys on page 3-5
for a description of the function keys.
If a key is pressed without using
Shift
, the
numbered item becomes active instead of
the special function key.
OK (
GREEN
) Indicates the operation is in the normal mode and no
errors have been detected.
T
EST
(
YELLOW
)
Indicates that the network interface is operating in a test
mode. This includes a self-test or a test loopback. When
lighted, this LED also indicates that normal data flow is
not occurring on the network interface.
E
RROR
(
RED
) Indicates an error such as a BPV, OOF, or CRC.
A
LARM
(
RED
) Indicates an alarm condition has been detected. When the
alarm condition is no longer valid, the OK LED activates
(turns on). To view an alarm condition, select the active
alarm menu item or select A
LARM
by pressing
Shift+8
. If
the alarm conditions have been corrected, the alarm which
caused the activation of the Alarm LED can be viewed
under the Unit History menu.
Table 3-1. Front Panel Descriptions
Name Description
- TSU 120 & 120e 1
- User Manual 1
- Trademarks: 2
- Safety Instructions 3
- Service Type REN/SOC FIC USOC 8
- Interference Statement 10
- Warranty and Customer Service 12
- LIMITED PRODUCT WARRANTY 12
- Training 15
- Training Fax (256) 963-6700 15
- Table of Contents 17
- List of Figures 23
- List of Tables 25
- Introduction 27
- Chapter 1. Introduction 28
- TSU Option Modules 29
- Installation 31
- Power Connection 32
- GROUNDING INSTRUCTIONS 32
- Chapter 2. Installation 33
- TSU 120 Interfaces 35
- IN and OUT test jacks 36
- T-MON test jack 36
- Power Up Testing 37
- Self-Test 37
- Initialization 37
- Power-Up Procedure 39
- Operation 41
- LED Descriptions 42
- CSU Status 42
- Chapter 3. Operation 43
- Shift+8 44
- Down arrows 45
- Data Field 47
- Display Field 47
- Data Port Identification 48
- Front Panel Menu Structure 49
- Alternate Methods of Control 50
- <CTRL> PTT 52
- Status Menu 55
- Chapter 4. Status Menu 56
- Clear (Shift+9) 56
- Active Alarms 57
- View History 58
- Port Status 58
- Remote Port 61
- ENET Status (TSU 120e only) 61
- Configuration Menu 63
- Chapter 5. Configuration Menu 64
- NETWORK (NI) 65
- Network (NI) Menu Items 65
- TSU 120 Clock Sources 67
- Base DSX-1 Timing 69
- See Figure 5-3 69
- (OPTION) 70
- Unit Menu 74
- Map Exchange (Map Xchng) 76
- Map In Use: A(B) 76
- MAP A MAP B 77
- Select DS0 Number 79
- Select Port 79
- INTERNAL 82
- EXTERNAL 82
- Menu Items Description 83
- Utility Menu 87
- Chapter 6. Utility Menu 88
- Set Passcode 89
- Time/Date 89
- Port Utility (Option Ports) 91
- ENET Address (TSU 120e only) 91
- Serial Number 91
- CMD Mode 91
- Test Menu 93
- Network Tests 95
- QRSS ALL DS0S 98
- Run Self-test 99
- Port Tests 100
- Chapter 7. Test Menu 101
- Clear (Shift+9) 101
- Cancel Tests 102
- Telnet/Terminal Menus 103
- Management Configuration 107
- Remote Menu Access 107
- Flash Download 112
- Quit Session 113
- Understanding SNMP 115
- Commands 116
- Messages 116
- TSU 120 SNMP Access 117
- SNMP Trap Configuration 118
- Step Action 119
- Understanding TR-08 121
- Table B-1 122
- TR-08 DS0 Conversion Table 123
- Network Pinouts 125
- Control In/Chain In 126
- Chain Out 127
- Nx56/64 DTE (V.35) 128
- Base DSX-1 (PBX) 129
- 10BaseT (TSU 120e only) 130
- System Messages 131
- Status Messages 132
- Appendix D. System Messages 134
- Specifications 135
- Appendix E. Specifications 136
- MANAGEMENT INTERFACES 137
- Chassis Specifications 137
- Environmental Specifications 138
Verwandte Produkte und Handbücher für Vernetzung ADTRAN TSU 120
Vernetzung ADTRAN Vanta 1335 Bedienungsanleitung
(15 Seiten)
(15 Seiten)
Vernetzung ADTRAN XRT Betriebsanweisung
(111 Seiten)
(111 Seiten)
Vernetzung ADTRAN Vanta 1335 Bedienungsanleitung
(13 Seiten)
(13 Seiten)
Vernetzung ADTRAN DE-4E Spezifikationen
(19 Seiten)
(19 Seiten)
Vernetzung ADTRAN T1-FT1 Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Vernetzung ADTRAN T200 T1 HDSL4 Spezifikationen
(18 Seiten)
(18 Seiten)
Vernetzung ADTRAN T1-FT1 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Vernetzung ADTRAN SHDSL T1 Bedienungsanleitung
(10 Seiten)
(10 Seiten)
(1 Seiten)
Vernetzung ADTRAN DE-4E Bedienungsanleitung
(8 Seiten)
(8 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 3.129 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern