ADTRAN 600R Spezifikationen Seite 155
- Seite / 196
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
61200600L1-1A © 2002 ADTRAN, Inc. 155
Total Access 600R System Manual Section 5 DLP-008
Prior to the start of the upgrade, the transfer status will display IDLE. During the TFTP upload, various
status messages display in T
RANSFER STATUS to indicate progress. The following table describes
these messages.
9. When the update has successfully completed, FLASH PROGRAMMED SUCCESSFULLY will display briefly
in the T
RANSFER STATUS field. This will be followed by a LOADED CODE VER X.X.X CHKSUM = XXXX
message. Finally the T
RANSFER STATUS field will display RESETTING...
The unit will restart immediately and resume operation. After giving the unit sufficient time to reboot,
the user may Telnet back into the unit and log in.
For WAN Upgrades
1. Telnet into the unit using FULL or SUPPORT levels (refer to DLP-003, Adding/Removing Telnet Users
and Changing Password Security Levels).
2. Verify the TFTP server is running on the network.
Verify that the unit can ping the TFTP server.
3. Go to the S
YSTEM UTILITY menu and select the UPDATE FIRMWARE menu; press <Enter>.
4. Go to the T
RANSFER METHOD menu and select TFTP.
5. Set the TFTP S
ERVER ADDRESS to the IP address of the machine running the TFTP server program.
6. Enter the filename of the update file into the TFTP S
ERVER FILENAME field.
7. Select S
TART TRANSFER to start the update. Enter Y to confirm the upgrade.
Message Meaning
Transferring... [X KB] Indicates communication with the TFTP network server has been
established and the update file is being transferred between the unit and
the TFTP network server.
Flash Programmed
Successfully
The unit has been upgraded successfully.
Loaded code
ver x.x.x
chksum = xxxx
Unit displays the version and checksum of the upgraded code.
Resetting.... Unit is power cycling.
RECV Error Unit will display this message if server filename is incorrect.
Host Timeout Unit will display this message if TFTP server address is incorrect.
idle The upgrade has not yet been initiated.
If using ADTRAN utilities, this will be the IP address that appears in the TFTP SERVER
S
TATUS window.
- TOTAL ACCESS 600R 1
- Trademarks 2
- To the Holder of the Manual 2
- Revision History 4
- Safety Instructions 5
- Warranty and Customer Service 12
- LIMITED PRODUCT WARRANTY 12
- SYSTEM DESCRIPTION 15
- 1. SYSTEM OVERVIEW 17
- 2. FEATURES AND BENEFITS 18
- Configuration and Management 18
- Software Upgradeable 18
- Network Interface 18
- LAN Interface 18
- CRAFT port 19
- T1.403-1995 (Annex B) 20
- ENGINEERING GUIDELINES 21
- 1. EQUIPMENT DIMENSIONS 22
- 2. POWER REQUIREMENTS 22
- Front Panel LEDs 22
- NTWK Connection 23
- Craft Port 24
- 10/100BaseT Connection 24
- AC Power Connection 25
- 5. DB-9 TO RJ ADAPTER 25
- 6. AT-A-GLANCE SPECIFICATIONS 26
- NETWORK TURNUP PROCEDURE 29
- 1. INTRODUCTION 31
- 2. TOOLS REQUIRED 31
- Contents of ADTRAN Shipment 31
- 4. GROUNDING INSTRUCTIONS 32
- AC Power 32
- AC Powered Systems 32
- 6. MOUNTING OPTIONS 33
- USER INTERFACE GUIDE 35
- Terminal Menu Window 38
- Menu Path 38
- Window Panes 39
- Moving Through the Menus 40
- Session Management Keystrokes 41
- Configuration Keystrokes 41
- Telnet Security Levels 43
- 3. MENU DESCRIPTIONS 44
- SYSTEM INFO 44
- SYSTEM INFO > SYSTEM NAME 44
- SYSTEM CONFIG 46
- SYSTEM CONFIG > MANAGEMENT 46
- SYSTEM CONFIG > SYSLOG 52
- SYSLOG using Terminal Mode 53
- CRAFT port log messages 56
- SYSTEM UTILITY 59
- INTERFACES 64
- INTERFACES (T1[0]) 64
- L2 PROTOCOL 69
- L2 PROTOCOL (T1[0]) 69
- L2 PROTOCOL (T1[0] - FRE) 74
- INACTIVE 77
- BRIDGE > CONFIG 81
- ROUTER > CONFIG 83
- OUTER > CONFIG > ROUTES 92
- ELAY ADDRESS 94
- LEAR COUNTS 96
- SECURITY 105
- SECURITY > FILTERS 105
- SECURITY > RADIUS SERVER 114
- ADIUS SERVER. The default is 115
- DS0 MAPS 116
- DS0 MAPS > ACTIVE MAP 116
- Setting up Routing Options 119
- Initial Setup 119
- DS0 Mapping 119
- IP Routing 120
- EFAULT GATEWAY 124
- Setting up Bridging Options 125
- Bridging 125
- DETAIL LEVEL PROCEDURES 127
- Introduction 129
- Prerequisite Procedures 129
- Tools and Materials Required 129
- Follow-up Procedures 130
- LOGGING IN TO THE SYSTEM 131
- SECURITY LEVELS 135
- DDRESS menu 142
- TELNETTING TO THE UNIT 145
- ASET port, the unit may 150
- For LAN Upgrades 154
- For WAN Upgrades 155
- TATUS field 158
- Follow-up Procedure 166
- COMMAND LINE 169
- ADTRAN UTILITIES 181
- 1. TELNET UTILITY 182
- Session Menu 182
- Edit Menu 183
- Options Menu 184
- Capture Menu 184
- Help Menu 184
- 2. VT100 UTILITY 185
- Port Menu 186
- 3. TFTP SERVER 187
- Server Menu 188
- Print Log 188
- 4. STATUS FIELD 189
- 5. METER FIELD 189
- 6. LOG FIELD 189
- CONTENTS 191
- SNMP manager 193
- 2. MIB COMPILATION ORDER 194
Verwandte Produkte und Handbücher für Telefone ADTRAN 600R
Telefone ADTRAN 1534/1544 Installationsanleitung
(52 Seiten)
(52 Seiten)
Telefone ADTRAN IP 601 SIP Betriebsanweisung
(35 Seiten)
(35 Seiten)
Telefone ADTRAN IP 601 SIP Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Telefone ADTRAN IP 700 Series Bedienerhandbuch
(85 Seiten)
(85 Seiten)
Telefone ADTRAN 606 Bedienungsanleitung
(11 Seiten)
(11 Seiten)
Telefone ADTRAN 624 Bedienerhandbuch
(264 Seiten)
(264 Seiten)
Telefone ADTRAN 624 Spezifikationen
(442 Seiten)
(442 Seiten)
Telefone ADTRAN 612 Bedienungsanleitung
(78 Seiten)
(78 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.663 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern