ADTRAN ATLAS 550 Bedienungsanleitung Seite 48
- Seite / 262
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 3. Operation
3-2 ATLAS 550 User Manual 61200305L1-1
When you begin the VT-100 session, you will be prompted for a password.
The default password is password (which is a Level 0 superuser password).
Youcanchange thispasswordusingthe A
CCESS
P
ASSWORDS
option, which
is only accessible through the terminal menu. See Access Passwords on page
6-15 for details. After your password is accepted, define the IP Address of
the ATLAS 550 to which you want to connect. The following Step/Action
chart describes this process.
Instructions for Setting Up an ATLAS 550 for VT-100 Terminal Mode
Step Action
1 Set the baud rate on the VT-100 terminal to 9600 baud (8/N/1).
2
Use the ADTRAN-provided VT-100 terminal adapter to connect
the COM port of a VT-100 compatible terminal, or equivalent, to
the eight-pin modular jack labeled
CONTROL/CHAIN IN
on the
rear panel or labeled CRAFT on the front panel.
This connection provides both local and remote configuration.
3
Press Enter repeatedly on the keyboard until the L
OGIN
menu
requiring a password appears.
4 Press Ctrl-R to refresh the display, if necessary.
Instructions for Defining the IP Address
Step Action
1
Obtain an IP address for the ATLAS 550 from your LAN
administrator.
2
Use the ADTRAN-provided VT-100 terminal adapter to connect
the COM port of a VT-100 compatible terminal, or equivalent, to
the eight-pin modular jack labeled CONTROL/CHAIN IN on the
rear panel or labeled CRAFT on the front panel.
This connection provides both local and remote configuration.
3
Press Enter repeatedly on the keyboard until the L
OGIN
menu
appears. Enter your password.
4
When the terminal menu opens, navigate the following path:
ATLAS 550 /S
YSTEM
C
ONFIG
/E
THERNET PORT
/IPA
DDRESS
5 Key in the entire IP address, and then press Enter.
You will need a default gateway if the LAN contains multiple
segments. Contact your LAN administrator for the appropriate
address.
- ATLAS 550 1
- TRADEMARKS 2
- Table of Contents 11
- List of Figures 25
- List of Tables 29
- Introduction 31
- Access Router 32
- Access Switch 33
- Additional Applications 34
- ATLAS 550 FEATURES 35
- Chapter 1. Introduction 36
- Installation 37
- GROUNDING INSTRUCTIONS 38
- SUPPLYING POWER TO THE UNIT 39
- MOUNTING OPTIONS 39
- Control/Chain In Port 40
- Control/Chain Out Port 41
- Ethernet Connection 41
- Alarm Relay Connection 42
- Network Connection 43
- Test Interface 44
- Frame Relay Specifications 44
- IP Router Specifications 45
- Option Slots 45
- INSTALLING OPTION MODULES 45
- Chapter 2. Installation 46
- Operation 47
- Chapter 3. Operation 48
- CONTROL/CHAIN IN 48
- USING TELNET 49
- Using the Front Panel 51
- CRAFT PORT 52
- FRONT PANEL LEDS 52
- Navigating the Terminal Menus 57
- Menu Path 58
- Window Panes 58
- Moving through the Menus 61
- Session Management Keystrokes 61
- Configuration Keystrokes 62
- Getting Help 62
- System Control Terminal Menus 63
- SECURITY LEVELS 64
- EVENT LOG 66
- RESOURCE USAGE 68
- CHAIN PORT SIGNAL 69
- CHAIN PORT TX 69
- INTERNAL 70
- SESSION TIMEOUT 71
- MAX TELNET 71
- SESSIONS 71
- ETHERNET PORT 71
- CHAIN PORT 72
- EVENT LOGGING 76
- SYSLOG SETUP 76
- REAL TIME CLOCK 76
- PASSWORDS 77
- LICENSES 78
- LARM RELAY 79
- HRESHOLD 79
- PDATE FIRMWARE 79
- None Selected 80
- Has not been attempted 81
- Module Update Complete 81
- UPDATE STATUS 82
- CONFIG TRANSFER 82
- SYSTEM UTILIZATION 83
- SYSTEM SELFTEST 83
- EBOOT SYSTEM 86
- ACTORY DEFAULT 86
- Module Terminal Menus 87
- Packet Manager 95
- PERFORMANCE 98
- Chapter 8. Packet Manager 100
- ENDPNT COUNT 106
- ENDPNTS SORT 106
- NABLE IQ STATS 108
- ORT ENABLES 108
- VIEW IQ STATISTICS 109
- OVERVIEW 115
- Chapter 9 115
- Chapter 9. Router 116
- IP MENUS 117
- NTERFACES 119
- SUBNET MASK 120
- FAR-END ADDRESS 120
- PROXY ARP 122
- PORT NAME 122
- IP ADDRESS 122
- DEFAULT GATEWAY 122
- TATISTICS 124
- IP FAST CACHE 128
- RELAY TABLE 129
- Dedicated Maps 131
- APS 1 THROUGH 5 132
- ORT TO/FROM 133
- Chapter 10. Dedicated Maps 134
- ACTIVATE TIME 136
- ENBL DAY 136
- IGNALING 137
- Dial Plan 143
- Interface Configurations 144
- UT#ACCEPT 145
- Chapter 11. Dial Plan 146
- IFCE CONFIG 147
- N#ACCEPT 148
- INTERFACE CONFIGURATIONS 152
- SWITCH TYPE 153
- FIRST DS0 153
- NUMBER OF DS0S 153
- OUTGOING NUMBER 153
- CONVERSION 153
- STRIP MSD 154
- SOURCE ID 156
- SWAP ANI/DNIS 156
- S AVAILABLE 157
- IGNALING METHOD 157
- X SEQUENCE 157
- INK AFTER ANI/ 157
- DIGIT SUPPRESSION 158
- DIRECT INWARD 158
- TRUNK NUMBER 158
- ALLED DIGTS 161
- RANSFERRED 161
- UTGOING CALLER 161
- OURCE ID 161
- WAP ANI/DNIS 161
- DS0S AVAILABLE 162
- SIGNALING METHOD 162
- DIAL ON OFFHOOK 164
- SPID LIST 166
- CREATING DIAL PLANS—EXAMPLES 168
- AT L A S 5 5 0 A 169
- ATLAS 550 B 169
- PKTENDPT 170
- PKTVOICE 173
- Menus for Network Termination 175
- Menus for User Termination 176
- Updating Firmware 177
- TFTP FIRMWARE UPDATES 179
- Updating Firmware using TFTP 179
- Schedule 180
- Current Update Status 180
- Chapter 12. Updating Firmware 181
- SNMP Management 183
- SNMP TRAPS 184
- Trap Destination List 184
- Standard Traps 185
- DS1 Traps 186
- Chapter 13. SNMP Management 187
- ADTRAN Utilities 189
- SysLog GUI 190
- Menu Bar 191
- RASE LOG FILES 192
- EFINE RED EVENTS 192
- ROPERTIES 192
- LEAR RED EVENTS 192
- TELNET UTILITY 193
- Chapter 14. ADTRAN Utilities 195
- VT-100 UTILITY 196
- ISCONNECT 197
- ILE TRANSFER 197
- EFRESH SCREEN 197
- TFTP SERVER UTILITY 198
- TFTP Download Complete 201
- System Event Logging 203
- ISDN CAUSE CODES 208
- CAUSE CODE LOG ENTRIES 210
- Technology Overview 213
- OSI Model and Frame Relay 213
- FRAME RELAY 215
- Virtual Circuits 215
- User-to-Network Interface 217
- Managing Network Congestion 219
- Frame Relay Examples 221
- Site Router 224
- Frame Relay 228
- Router Examples 231
- CENTRAL-SITE ROUTER 232
- Appendix D. Router Examples 233
- Troubleshooting 235
- Misconfiguration 236
- Frame relay link is down 237
- Appendix E. Troubleshooting 238
- Acronyms and Abbreviations 239
- Glossary 241
- Appendix G. Glossary 242
- Numerics 253
- Product Support Information 261
Verwandte Produkte und Handbücher für Vernetzung ADTRAN ATLAS 550
Vernetzung ADTRAN ISU 128 Bedienungsanleitung
(152 Seiten)
(152 Seiten)
Vernetzung ADTRAN 3360.9VU01 Spezifikationen
(94 Seiten)
(94 Seiten)
Vernetzung ADTRAN MX2800 Bedienungsanleitung
(142 Seiten)
(142 Seiten)
Vernetzung ADTRAN 4202023L4 Bedienungsanleitung
(68 Seiten)
(68 Seiten)
Vernetzung ADTRAN 1204006L1 Bedienungsanleitung
(175 Seiten)
(175 Seiten)
Vernetzung ADTRAN 1200287L1 Bedienungsanleitung
(204 Seiten)
(204 Seiten)
Vernetzung ADTRAN 1204002L1 Bedienungsanleitung
(171 Seiten)
(171 Seiten)
Vernetzung ADTRAN TA 544 Bedienerhandbuch
(162 Seiten)
(162 Seiten)
Vernetzung ADTRAN MX2800 Bedienungsanleitung
(220 Seiten)
(220 Seiten)
Vernetzung ADTRAN MX3216 Spezifikationen
(190 Seiten)
(190 Seiten)
Vernetzung ADTRAN T200 FNID Spezifikationen
(76 Seiten)
(76 Seiten)
Vernetzung ADTRAN Stub Routing Betriebsanweisung
(132 Seiten)
(132 Seiten)
Vernetzung ADTRAN 1200214L1 Spezifikationen
(176 Seiten)
(176 Seiten)
Vernetzung ADTRAN TSU 120 Bedienungsanleitung
(143 Seiten)
(143 Seiten)
Vernetzung ADTRAN 1500 Bedienungsanleitung
(27 Seiten)
(27 Seiten)
Vernetzung ADTRAN 6330 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.203 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern