ADTRAN 1200214L1 Spezifikationen Seite 89
- Seite / 176
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 7. Configuring the DCE Port
61200214L1-20 IQ Probe User Manual 7-7
DBU Call Order Number
This determines the order in which a list of backup locations will be dialed.
This applies only to auto DBU processes that are triggered by port failure.
If all DBU C
ALL
O
RDER
entries are set to N
ONE
, then the first entry with a
DBU P
HONE
N
UMBER
will be used.
CIR (Kbps)
Enter the CIR in kbps for the corresponding DLCI. The information is sup-
plied by your service provider and must be entered for each PVC to ensure
accuracy of statistical information.
Seq Num Checking (SEQ #)
Set to E
NABLE
only if there are IQ products on both ends of the PVC. When
enabled, the IQ Probe tags each frame with a sequence number which is
then used by the remote IQ device to detect lost packets. Lost packet
counts are given in the S
TATISTICS
menus.
Delay Measurement (PVC DELAY)
Set to E
NABLE
only if there are IQ products on both ends of the PVC. When
enabled, the IQ Probe periodically transmits a loopback frame to the re-
mote IQ device which is then returned to measure round trip delay of each
PVC. Minimum, maximum, and average delay measurements are given in
the S
TATISTICS
menus.
Stats Option (STATS OPT)
This option prioritizes PVCs for S
TATISTICS
counts. The IQ Probe tracks
statistics for a limited number of the PVCs that pass through. This number
is determined in the M
AX
PVC C
OUNT
field (see Maximum PVC Count
(MAX PVC COUNT) on page 7-5). The three choices for this field are de-
scribed below.
Auto
If set to A
UTO
, then statistics will be logged for this PVC if the M
AX
PVC
C
OUNT
has not been exceeded. The A
UTO
selection designates a PVC as sec-
ond priority to a PVC set to E
NABLED
.
Enabled
If set to E
NABLED
, then statistics will be logged for this PVC if the M
AX
PVC
C
OUNT
has not been exceeded. A PVC set to E
NABLED
is designated as a
higher priority than one set to A
UTO
.
- IQ Probe 1
- Digital Services 7
- Save These Instructions 12
- Table of Contents 15
- List of Figures 25
- List of Tables 27
- Introduction 29
- UNDERSTANDING FRAME RELAY 30
- SNMP MANAGEMENT 31
- DIAL BACKUP OPERATION 32
- INTERFACE CARD OPTIONS 33
- 4-Wire Switched 56 DBU Card 33
- V.34 DBU Card 33
- ISDN DBU Card 33
- DCE Card 33
- Chapter 1. Introduction 34
- Installation 35
- Power Up 36
- REAR PANEL 37
- Chapter 2. Installation 38
- DBU Interface Card Slot 39
- DCE Interface 39
- DTE Interface 39
- LAN 10BaseT Interface 40
- Control Port 40
- Operation 41
- Numeric Keypad 42
- Next, Prev, Add, Delete 42
- Chapter 3. Operation 43
- LED Descriptions 44
- FRONT PANEL OPERATION 45
- CNTL + L 46
- Local Login Via Telnet 48
- Enter to continue… 49
- Remote Login Via Telnet 51
- ANY KEY TO CONTINUE 53
- IQ PROBE MENU STRUCTURE 55
- MAIN MENU 55
- Applications 57
- Baud Rate 58
- Control Port Mode 58
- Out-of-Band Management 59
- In-Band Management 61
- IP Address 62
- Chapter 4. Applications 64
- ANAGEMENT 64
- DIAL BACKUP APPLICATION 67
- AUTO DBU Enable 68
- With PVC Inactive: Enable 68
- Configuration Overview 71
- DTE Port Configuration 77
- Frame Relay Options (FR OPTS) 80
- Always On 82
- Follows Network (FOLLOW NET) 82
- Configuring the DCE Port 83
- Management DLCI 1 and 2 Mode 86
- PVC Options (PVC CONFIG) 87
- Disabled 90
- Dial Backup Configuration 91
- Auto DBU 94
- DBU Options 94
- DBU Criteria 95
- DBU Timers 96
- Tone/Pulse 97
- Max Baud Rate 97
- Sync/ Async 97
- Switch Type 97
- Call Screening 98
- System Configuration 99
- Subnet Mask 100
- Read Community (RD COMMUNITY) 101
- Trap Mgr Options 101
- Add (ADD key on front panel) 102
- Protocols 1 and 2 103
- System Time/Date 103
- LEDs Reflect 104
- USING THE FRONT PANEL 104
- Statistics 105
- Hot Keys 107
- DTE Port Statistics 108
- Chapter 10. Statistics 109
- DCE Port Statistics 111
- ONFIGURATION 113
- Layer 3 Statistics 116
- Top Talker 120
- DBU Port Statistics 121
- DLCI Statistics 125
- DLCI List 130
- System Statistics 131
- Control Signal Status Screen 133
- VERSION CHKSUM 136
- VER 601a 3F34 136
- Chapter 11 137
- PVC Loopback 138
- Chapter 11. Testing 139
- PVC Active/Inactive/Undefined 140
- Test Active/No Test Active 140
- TATISTICS 141
- Pings Transmitted (PINGS TX) 142
- Ping Responses (PINGS RX) 142
- Chapter 12 143
- Appendix A 145
- Appendix A. Pinouts 146
- Specifications Summary 153
- Acronyms and Abbreviations 155
- Glossary 159
- Appendix D. Glossary 160
- Numerics 171
- Post-Sale Support 175
- Repair and Return 175
Verwandte Produkte und Handbücher für Vernetzung ADTRAN 1200214L1
Vernetzung ADTRAN TSU 120 Bedienungsanleitung
(143 Seiten)
(143 Seiten)
Vernetzung ADTRAN 1500 Bedienungsanleitung
(27 Seiten)
(27 Seiten)
Vernetzung ADTRAN 6330 Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Vernetzung ADTRAN 600 SERIES Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Vernetzung ADTRAN TSU LT Bedienungsanleitung
(77 Seiten)
(77 Seiten)
Vernetzung ADTRAN MX2800 Bedienungsanleitung
(200 Seiten)
(200 Seiten)
Vernetzung ADTRAN 1204002L1 Bedienungsanleitung
(183 Seiten)
(183 Seiten)
Vernetzung ADTRAN ATLAS 810 Plus Spezifikationen
(188 Seiten)
(188 Seiten)
Vernetzung ADTRAN T3SU 300 Bedienungsanleitung
(141 Seiten)
(141 Seiten)
Vernetzung ADTRAN T200 FNID Betriebsanweisung
(16 Seiten)
(16 Seiten)
Vernetzung ADTRAN Express 3110 Bedienerhandbuch
(116 Seiten)
(116 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern