ADTRAN 1200287L1 Bedienungsanleitung PDF herunterladen (Seite 40)

Chapter 3. Configuration

3-2 MX2810 M13 User Manual 61185001L1-1

Figure 3-2. Configuration Menu Tree

1. Network Interface

2. T1/E1 Interface

4. Utilities

Defaults = *

2. M13*

1. C-BIT

2. Local

1. Loop*

9. Loopback Timeout

2. B

1. A*

2. G.747 (3 x E1)

1. M12 (4 x T1)*

2. Enabled

3. Auto Enable*

1. Disabled

2. CSU

3. NIU

1. Disabled*

2. Short (0-225 ft.)*

1. Long (225-450 ft.)

5. Save Configuration & Alarm Log

1. State

T1 # 1-28

10-16. DS2 # 1-7

T1 # 1-28

T1 # 1-28

T1 # 1-28

4. Loopback Detection

2. Line Coding

2. Line Length

3. Timing

4. Remote Loopbacks

1. Framing

5. XCV Threshold

5. Circuit Protection

6. Line Identification

7. XCV Threshold

2. B8ZS*

1. AMI

2. FEAC/C-BIT*

3. FEAC

4. C-BIT

1. Disabled

2. IE-3

3. IE-4

4. IE-5

1. Disabled*

5. IE-6

2. IE-3

3. IE-4

4. IE-5

1. Disabled*

5. IE-6

2. 1 min.

3. 5 min.

4. 10 min.

1. Disabled

5. 15 min.

6. 30 min.

7. 45 min.

8. 1 hour*

3. Line Length

DS3 Configuration

DS2 Configuration

Protection Configuration

Miscellaneous

6. Active Controller

7. Max Switch Threshold (3)*

8. Min Switch Period (10)*

3. System Management

Mgmt Options

System Security

Alarm Relays

Date & Time

Miscellaneous

SNMP Mgmt Options

5. Trap IP Address

8. Write Community Name

6. Trap Generation

9. Trap Community Name

7. Read Community Name

1. Controller Traps

4. DS2 Alarm Traps

2. Power Supply Alarm Traps

5. T1/E1 Alarm Traps

6. MIB II Standard Alarm Traps

3. DS3 Alarm Traps

1. Emergency

4. Error

2. Alert

5. Warning*

6. Notice

7. Info

8. Debug

3. Critical

1. Local 0*

4. Local 3

2. Local 1

5. Local 4

6. Local 5

7. Local 6

8. Local 7

3. Local 2

1. Local IP Address

4. Alarm Relay Configuration (all Disabled*)

2. Gateway IP Address

3. Subnet Mask

16. Circuit Identification

17. Syslog Setup

18. Autosave (Enabled)*

19. Autoprogram Cards

(Enabled)*

1. Load Default Settings

4. System Reset

2. Update FLASH Software

3. Configuration Transfer

2. 133-266 ft.

3. 266-399 ft.

4. 399-533 ft.

1. 0-133 ft.*

5. 533-655 ft.

2. Enabled*

1. Disabled

2. Enabled*

1. Disabled

15. Time

14. Date

T1 # 1-28

T1 # 1-28

2. Update via TFTP Server

1. Via XMODEM

11. Terminal Timeout (15 Min.)*

10. User Account Management

13. IP Hosts (0.0.0.0)*

12. IP Security (Disabled)*

2. Host IP Address (0.0.0.0)*

1. Transmission

4. Host Facility

3. Severity Level

2. Local Facility ID Code

1. Unit ID

4. Local Frame ID Code

3. Local Location ID Code

6. Local Equipment Code

5. Local Unit Code

Far-End Location ID Code

Far-End Facility ID Code

Far-End Unit Code

Far-End Frame ID Code

Far-End Unit Code

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 203 204

Kommentare zu diesen Handbüchern

Keine Kommentare